Easy Guide to Repair/ Change IMEI Of Your MTK / Android Smartphone and Devices (Without PC)

Repair or Changing the IMEI of your MTK / Android is now possible, this includes for MTK 6577 / 6575 android devices, e.g:- Tecno, Gionee, Infinix, and few others, and this post will show you how to do it using Mobile Uncle Tools.

NOTE:

•  This tweak was initiated for the main purpose of educating our readers, we will Not be held responsible if this info is used for any illegal activity.
•  We reserve the right that if you get your device bricked during the process stated below, We won't be held responsible for any Damages.

Meanwhile this post should be useful if your MTK phone is having problem registering your SIM to your network. Probably due to change of location.

That's by the way, but we assure damaging your device during procedure is nothing to worry about, you'll get it successfully done within seconds if you follow the Steps below carefully:

REQUIREMENTS For changing/Fixing the IMEI number on your MTK android :

1.  A Rooted Android (MTK 6577 / 6575)

2.  A valid IMEI number

3.  The  MobileUncle MTK Tools Engineering Mode MTK from PlayStore

N.B

Note that when you use IMEI number of your old unused mobile phone, be sure to never insert a SIM of same network again.

i.e >> If you use a Glo sim on a Blackberry (or any other phone), after you copied and use the Blackerry's IMEI into your Android, your Glo will work fine on your Android. But be sure not to insert that same Glo SIM into the Blackberry again, If you do and switch it on, the sim will not register to the network

1. Dial *#06#, write down your Default IMEI, or Simply Back it up on ur SDcard

2. Run the MobileUncle tools App

3. Go to >> Engineer Mode >> Engineer Mode (MTK)

4. Scroll down to CDS Information

5. CLICK >> Radio Information

You'll see something like:

Phone1 -

Phone2 -

In that select Phone2, because in most of these Chinese cloned phone, the 1st Sim which is a 3G will work perfectly. Problem only happens when we insert the second sim. Such cases are experienced if after you check, you can see the IMEI of 1st sim starting with 35xxxxx and the 2nd will start with 88xxxxxxxx. That is why the second sim is not able to register to the network, because its not in international formatted IMEI. So usually we need to change the IMEI of Phone 2.

When you select any of  Phone1 or Phone2 - you'll find AT+ __________

Inside there input your new IMEI number,

click >> SEND AT COMMAND

That's all!

EXTRA TIP UPDATED:

Some devices are different and may want to prove stubborn, so here's an extra tip just in case the steps above didn't work for you.

TO CHANGE IMEI FOR  SIM1 OR DEVICES WITH ONE-SIM ONLY:

Type the following command then Press Enter or click SEND AT COMMAND

echo ‘AT+EGMR=1,7, “IMEI_NUMBER”

TO CHANGE IMEI FOR SIM2 (DUAL SIM):

If your phone is dual-sim, type this

command:  echo ‘AT+EGMR=1,10,

“IMEI_NUMBER” ‘ >/dev/pttycmd1

Press ENTER or SEND AT COMMAND

UPDATE FOR THOSE USING INFINIX HOT X507

if you get errors saying "Sending Failed" or "module not supported for device errors"

When you get the AT+EGMR

Make sure you leave a Space between ‘AT+EGMR= (and) the IMEI Number

For example > ‘AT+EGMR=[space]"2345XXXXX"

Now Click SEND AT command, You'll get response "AT command is mSent"

Now restart your Infinix Hot. That's all.

Yes we are done… now you can restart the phone and check the IMEI. See if it worked by dialing *#06#

EXTRA TIP: FOR THOSE USING GLO NG

You can get 3gb and use it to browse after you change it to IMEI of Blackberry phone.

Activate a Glo BIS Plan.

Comonth to 777 (3GB) for 1,000Naira

Coweek to 777 (700Mb) for 400Naira

Set APN - blackberry.net

and you are good to go. Enjoy the Speed!

Found this Helpful? You can click our Share Buttons to Bookmark this page and let friends know about it.

Your Comments are also welcome.